Heat Treat Home      Event Overview      To Register      ASM Homepage

			Back to "Meet the Author" Search	Back to Main Search
Meet the Author
Location: Detroit Hall (COBO Center)
(Please check final room assignments on-site).
Session Description:
		Curtains in Continuous Furnaces
		Effectively Design Heat Treat Processes Using Computer Simulations
		Modern Gas Quenching Chambers Supported by SimVaCPlus™ Hardness Application
		Is 33% Increase in Production Rate From an Existing Brazing Furnace Possible?
		Gas Recycle Systems for Heat Treating Operations
		Optimizing Axle Scan Hardening Inductors
		Systematic Analysis of Induction Coil Failures and Prevention
		Induction Hardening of Gears and Critical Components
		Increasing Inductor Lifetime by Predicting Coil Copper Temperatures
		40 Induction Systems in 40 Minutes, an Overview of Induction Processes
		Saving Energy and Operating Costs with Flux Concentrators
		Effect of Nitriding on the Fatigue Properties of Continuously Cast Gray Irons
		Batch Tracking in Aluminum Heat Treating
		Optimization of Oxygen-free Heat Treating
		The Nitrocarburizing of Plain Carbon Steel Automotive Components
		Fatigue Studies and Characterisation of Induction Tempered Welded Steel Tubes
		Historical Review of Residual Stress in Quenched Fe-Ni Alloy Cylinders and Explanation of its Origin Using Computer Simulation
		Use of Intensive Quenching to Reduce the Carburizing Cycle of the Manufacture of Crosses for the Automotive Industry
		High Pressure Gas Quenching using the “Step Quenching Process” for improvement of part quality, cost and mechanical properties
		The Contribution of Dr. George E. Totten to Unitize World Heat Treatment R & D and Up Date State of the Quenching and Control of Distortion
		Applying CFD to Characterize Gear Response During an Intensive Quenching Process
		The Benefits of Using a 3 Gas Mixture Low Pressure Carburizing (LPC) for High Alloy Steels
		Improving Gear Performance by Intensive Quenching
		The Analysis Of Gas Flow In The Wind Tunnel Of High Pressure Gas Quenching Furnace
		Optimal Spray Characteristics in the Air-Assisted Water Spray Cooling of a Downward-Facing Heated Surface
		Transportation: the Tail that can Wag the Dog of Manufacturing
		Study of Brazing Process variation Parameters Effects on the Copper- Beryllium Alloy Joints Quality
		Thermal Spray Coatings On An Aged 7475 Aluminum Alloy Substrate
		Fabrication and Heat Treatment of Aluminum Automotive Components
		Microwave Processing and Heat Treating of Metals
		Step by Step Justification for Process Change
		Metallographic Technique for Revealing Prior austenite Grain Boundaries and Multiphase Microstructure in Steels
		Effect of Forging Conditions on the Microstructure and Mechanical Properties of Microalloy Steel
		Effects of Quenching Variables on the Fracture Toughness of 0.3C Hypo-Eutectoid Plain Carbon Steel
		Effects of T6 Heat Treatment with Residual Heat of Casting on Microstructure and Mechanical Properties of 319 Aluminium Alloy Castings
		Effect of Heat Treatment Cycle on the Mechanical Properties of Machinable Austempered Ductile Iron
		Expert Systems For Heating Systems Programming
		Heat Transfer Characteristics of Laminar Methane/Air Flame Impinging on a Flat Surface
		Optimal Control of Induction Surface and Through Heated Rods Bars and Wires
		Method for Producing a Powerful Plasma Formation for Materials Processing
		The Effect Of Aluminium On Isothermal Oxidation Resistance Of Austenitic Heat Resistant Steels
		Effectiveness of Hot Plastic Deformation and Austempering Combinations for the Gears Manufacturing from ADI
		The Aging Behavior of AA7136 Wrought Aluminum Alloy
		Evaluation of Aging Response of Al-Cu-Mg-Si Based Cast Aluminum Alloy and its Effect on Tensile Property
		Numerical Simulation of High Pressure Gas Quenching Process of Workpieces
		Laser Heat Treatment of Steels
		Special Heat Treatment Practices for Aerospace Aluminium Alloys
		On the Influence of the Process of Carbonitriding in Smouldering Discharge on the Properties of 25CrMnSiNiMo Steel
		Tribology of Conformal Gears with Advanced Material Systems
		Atmosphere Recycling with H2Gen's MARSTM: A New Method to Achieve Atmosphere Cost Reduction and Improved Product Quality
		Three Point Bending Behavior of Orthodontic Thermo-Active Nitinol Wires
		Electric Resistivity Evalution of the Fe – 31 Mn – 7,5 Al – 1,5 Si – 1,0 Calloy
		Plasma Nitriding of AISI H13 Tool Steel With Different Microstructures
		Metallurgical Insights of Induction Hardening
		Integrated Heat Treatment – System for Precise Die Hardening in Automotive Industries
		Effect of Post-spray Heat Treatment on Mechanical Properties of Ni-TiC Composite Coatings Produced by Cold Gas Dynamic Spray
		New Cost-effective Equipment for Generating Hydrogen Atmospheres
		New Instrument Simplifies Shim Stock Analysis for Carburizing Atmospheres